Capacitive rod sensor, PTFE
Product number:
4692395
Manufacturer:
SCAT Europe GmbH
Packaging information:
Description
The capacitive rod sensor is used for capacitive level measurement in combination with Safety Waste Caps. Switch amplifier necessary (not included). M12x1 thread.
Scope of supply:
Rod sensor with LED display, 2 m cable
Scope of supply:
Rod sensor with LED display, 2 m cable
Properties
| Manufacturer Article Number: | 108277 |
|---|---|
| Material: | PTFE |
Skip product gallery
Flexible connecting system for DURAN® GL 45 flasks
From
€2.65*
Fittings for SafetyCaps / SafetyWasteCaps
From
€19.90*
Exhaust filters V3.0, with change indicator
From
€59.90*
Air valves Generation 2.0 for SafetyCaps
From
€24.90*
Exhaust Filter, PP
From
€85.00*
Safety Waste Caps SymLine®, electrostatic conductive
From
€291.10*
Thread adapters for SafetyCaps / SafetyWasteCaps, female / male thread
From
€29.90*
Air valves for Eluent SafetyCaps
From
€13.10*
HPLC Waste disposal set 1, V2.0
From
€149.00*
Exhaust filters V3.0, with change label
From
€88.90*
Exhaust filters for Waste SafetyCaps
From
€69.30*
Similar products
For safe transfer of liquid media within a closed and sterile system (evaporation is reduced).Screw closure GL 45 with two, three or four ports GL 14 threadAutoclavableTemperature restistant up to max. 140 °CFlexible modular systemSterile pressure equalisation is possible through use of a membrane filterUnused ports can be provided with a blind cap
Fittings with integrated ferrule for SafetyCaps and SafetyWasteCaps.Use the blind plugs to tighten connectors which are temporarily inactive or not in use.
The exhaust air filters are equipped with three different activated carbon layers, which bind acids and alkalis and adsorb organic solvent vapours. Depending on the required capacity, filter with different service lifes are available.Filter media with a very high performance spectrum for acids and alkalisOptimised for binding buffer solutions and solvent vapoursWith splash guard1500 m²/g adsorption surface area
Thread size UNF 1/4" 28GLuer Lock adapterPTFE FilterValve membrane blocks vapours and opens at negative pressureIt is recommended to replace the valve every 6 monthsWith change indicator and labelling field for timely change
Lid with integrated ventilation openings and service life indicator. The filling of activated carbon is protected by two porous membranes made of PE. This allows an unobstructed flow of exhaust air, solvents are adsorbed by the activated carbon and only filtered air streams out.
Connection systems for waste containers with electrical level control system (SymLine built-in signal box or SCAT signal box T1/T5). The closed safety systems ensure reliable protection in the laboratory. Connection GL 25.
Use SafetyCaps and SafetyWasteCaps also for bottles with GL40 or GL38 thread. Further adapters in different thread sizes are available on request.
Air valves prevent the formation of vacuum in HPLC bottles.PTFE membrane1/4"-28 thread portWith timestrip sticker
Waste disposal set consisting of:Safety Waste Cap GL 452 x PFA fitting 2.3/3.2 mm OD1 x PP tube connector 5,0 - 11,5 mm ID5 l canister, HDPEExhaust filter M, with splash guard and change indicator
The exhaust air filters are equipped with three different activated carbon layers, which bind acids and alkalis and adsorb organic solvent vapours. Depending on the required capacity, filter with different service lifes are available.Filter media with a very high performance spectrum for acids and alkalisOptimised for binding buffer solutions and solvent vapoursWith splash guard1500 m²/g adsorption surface area
The exhaust filter cleans the exhaust air of HPLC waste. The activated carbon in the exhaust filter is optimised for the absorption of organic solvent vapours. With timestrip sticker for timely replacement of the exhaust filter.